MITSUBISHI Other Motor Related Components

Batteries, battery cases (battery purchased separately), battery cables, and battery relay cables for MELSERVO-J4 series.

[Features]
· A lineup including rotary servomotors, linear servo motors and direct drive motors from 50W to 220kW.

The MR-JE-_B servo amplifier is connected to controllers, including a servo system controller, on the highspeed synchronous network SSCNET III/H. The servo amplifier directly receives a command from a controller to drive a servo motor.
SSCNET III/H achieves high-speed communication of 150 Mbps full duplex with high noise tolerance due to the SSCNET III optical cables. Large amounts of data can be exchanged in real-time between the controller and the servo amplifier. Servo monitor information can be stored in the upper information system and used for control.
With one-touch tuning and real-time auto tuning, you can easily and automatically adjust the servo gains according to the machine.
The tough drive function, drive recorder function, and preventive maintenance support function strongly support machine maintenance.
The servo amplifier has a USB communication interface. Therefore, you can connect the servo amplifier to the personal computer with MR Configurator2 installed to perform the parameter setting, test operation, gain adjustment, and others.

Other products from Mitsubishi Electric.
[Features]
· Connection cable: for connection with operation panel and unit parameter.
· Relay terminal block cable: for MR-J3-A (CN1), MR-J3-DUA (CN1), MR-J3-D01 (CN10).
· Battery: for MR-J3-A/B/T, MR-J3-DUA/DUB (necessary for absolute position detection system).
· Setup software: MR Configurator servo setup software for PC
· Each part number is an individual product. They are not set products.

・ For MR-J5-G/MR-J5-A
Batteries for MR-J4-GF_/GF_-RJ, MR-J4W2-0303B6, MR-J4-03A6/03A6-RJ

Features
• Complete transitions in a short time by using existing wiring and mounting holes.
• This renewal tool allows replacements to be made in stages, such as primary replacement of only the amplifier or secondary replacement up to the motor.
• The servo amplifier can be replaced independently, without replacing the host controller or SSCNET cable.
• The MR-J2S servo amplifier motor can be controlled with the standard MR-J4 servo amplifier.
• The encoder conversion cable is available as a single part.

The servo amplifier has position, speed, and torque control modes. In the position control mode, the maximum pulse train of 4 Mpulses/s is supported. Further, it can perform operation with the control modes switched, e.g. position/speed control, speed/torque control and torque/position control. Hence, it is applicable to a wide range of fields, not only precision positioning and smooth speed control of machine tools and general industrial machines but also line control and tension control.
The servo amplifier supports profile position/velocity/torque mode that drive motors with communication from the controller. By specifying target position, target speed, acceleration time constant, and deceleration time constant, a position command is created in the servo amplifier and the motor will be driven.
With built-in positioning function, the positioning operation can be performed by using point table method or indexer method. Suitable for assembling a simple positioning system or for simplifying the system.
Drive motor, monitor, and parameter setting can be done with CC-Link IE field network Basic, SLMP, Modbus/TCP and various Modbus RTU open networks by installing the general-purpose Ethernet connector and RS-485 communication connector in each port.
With one-touch tuning and real-time auto tuning, you can automatically adjust the servo gains according to the machine.
The tough drive function, drive recorder function, and preventive maintenance support function strongly support machine maintenance.
The servo amplifier has a USB communication interface. Therefore, you can connect the servo amplifier to the personal computer with MR Configurator2 installed to perform the parameter setting, test operation, gain adjustment, and others.

If the generated regenerative power is large and the regenerative capacity of the built-in regenerative resistor of the servo amplifier is insufficient, use the regenerative option. As the regenerative capacity improves, and the generated regenerative power can be consumed.

Used for connection of the parameter unit and servo amplifier.

Power cable for MR-J4W2/J4W3

This reactor enables users to boost the servo amplifier’s power factor and reduce its power supply capacity.
As compared to the AC reactor, the DC reactor is more recommended since the DC reactor is more effective in power factor improvement, smaller and lighter, and its wiring is easier. (The DC reactor uses 2 wires, while the AC reactor uses 6 wires.)
If the generated regenerative power is large and the regenerative capacity of the built-in regenerative resistor of the servo amplifier is insufficient, use the regenerative option. As the regenerative capacity improves, and the generated regenerative power can be consumed.

Features
• Complete transitions in a short time by using existing wiring and mounting holes.
• This renewal tool allows replacements to be made in stages, such as primary replacement of only the amplifier or secondary replacement up to the motor.
• The servo amplifier can be replaced independently, without replacing the host controller or SSCNET cable.
• The MR-J2S servo amplifier motor can be controlled with the standard MR-J4 servo amplifier.
• The encoder conversion cable is available as a single part.

Features
• Complete transitions in a short time by using existing wiring and mounting holes.
• This renewal tool allows replacements to be made in stages, such as primary replacement of only the amplifier or secondary replacement up to the motor.
• The servo amplifier can be replaced independently, without replacing the host controller or SSCNET cable.
• The MR-J2S servo amplifier motor can be controlled with the standard MR-J4 servo amplifier.
• The encoder conversion cable is available as a single part.