Standard/Configurable Length Panel Clamp for Aluminum Frames

Dimensional Drawing of Panel Mounts

Specification Table of Panel Mounts

Product Overview of Panel Mounts

It is inserted into the frame groove when installing the panel.
Only compatible with joint bracket connections.

■ Product type

How to Use Panel Mounts

■ How to select Panel Mountss and economy Panel Mountss (examples of use)

Panel thickness: 5mm
Frame	HFS5	HFS6	HFS8 HFS8−45
Dimensions	HSCP1H HSCPF1H NSCP1H	HSCP3H HSCPF3H NSCP3H	HSCP5H HSCPF5H NSCP5H

 

Panel Thickness 3mm
Frame	HFS5	HFS6	HFS8 HFS8-45
Dimensional Drawing	HSCP3H HSCPF3H NSCP3H	HSCP5HN HSCPF5HN NSCP5HN	HSCP7H HSCPF7H NSCP7H

Use Case
Easily removed with scissors or a cutter
It can be cut.
Cut the corners at 45 degrees
This will make it look better.

<After assembly>

Panel Mounts

■ Summary

This is a method of fitting the panel into the groove of the frame.
Since there is no need to drill holes in the panel and no screws are required, it is recommended for those who place importance on design.
Screw joint, center joint, single joint, first-in double joint,
Can only be used when assembling with a post-insertion double joint.

■ Installation method

The panel size must be determined based on the fastening materials so that there is no interference between the panel and the fastening materials.
(1) Fasten the three frames together with blind joint parts.
(2) Insert the panel into the frame groove.
(3) Cut the Panel Mounts or inverted groove cover to the frame size and insert it into the gap.

6 Series
Insert the panel clamp into the gap.

 

Parts Selection Method of Panel Mounts

①Aluminum frame: Additional processing for blind joints (single joint: wrench hole processing)
②Aluminum frame: Additional processing for blind joints (single joint: D-hole processing)
③Blind joint
④Panel: Additional cutout

Thickness 3mm (5 series)
5mm (6/8/8-45 series)

size
Leave 1mm clearance on each side.
Panel vertical width (A) = frame inner dimension (X) + frame groove inner depth - clearance (1mm x 2)
Panel width (B) = Frame inner dimension (L2) + Frame groove inner depth - Clearance (1mm x 2)

 

■ Groove Internal Depth

5 Series	6 Series	8 Series	8-45 Series
6mm×2	9mm×2	12.5mm×2	13mm×2

Additional Processing of Panel Mounts

Aluminum frame blind joint cutout

Alterations	Aluminum frame blind joint cutout
Code	F□□・E□□・J□□・K□□
Spec.	We will make clearance cuts for blind joints in aluminum frames. [ ! ] The play due to expansion and contraction of the plates caused by temperature differences is not taken into consideration. [ ! ] The longitudinal direction of all cutouts is on the A dimension side. [ ! ] Applies to T=3 and 5 only Designation method FS 6 Frame type Joint Type Notch position (from the diagram above) [ ! ] Only applicable to standard size

By joint Cutout shape	Simple Joint kit	Single joint kit		Pre-inserted double joint kit		Center Joint	Post-insertion double joint
		Single Joint Kit standard type	Single Joint Kit narrow type, Screw joint kit	Standard Type	Eccentric nut type
	(Ex 1) (Ex 2) In Example 2, no panel cutout is required.		[ ! ]The illustration shows the Single Joint Kit Narrow Type.			(Ex 1) (Ex 2)

⑤ Panel Mounts (posterior insertion panel hold/panel hold clamp also acceptable)
Length: 1.Inside frame vertical -1mm, 2.Inside frame horizontal -17mm (-1mm if cutting corners at 45 degrees)
Thickness: Please select a Panel Mounts with a thickness equal to the frame groove width minus the panel thickness.
Additional Work: Corners cut at 45 degrees (You can also cut them yourself with scissors, etc.)

6 Series
Insert the Panel Mounts into the gap.

Use Case
Easily removed with scissors or a cutter
It can be cut.
Cut the corners at 45 degrees
This will make it look better.

<After assembly>

 

Select the Panel Mounts model based on the thickness of the aluminum frame and panel.

*If you use a post-insertion panel hold and a panel hold clamp instead of a Panel Mounts, you can attach the panel after assembling the frame.
*The plate or panel can be inserted by turning the groove cover resin soft over and inserting it inside the groove.
*This product is designed for panel thicknesses of 3mm and 5mm.
Plates with thicknesses of 1mm and 8mm may be difficult to insert, so we do not recommend them. Please use at your own discretion.