VAC Series Carbide 4-Flute Uneven Lead Long Neck Radius End Mill
Brand :
MISUMI
Caution
Product Description
[Features]
·Effective for deep cutting due to long neck type
·Ultra-fine particle cemented carbide base material and coating with excellent adhesion and heat resistance are adopted
·Can process heat-treated steel up to 50HRC
·Cutting edge radius also reinforced cutting edge rigid
·Can be regrinded. Please refer to the page dedicated to "regrinding service" for usage procedures, range of services, prices, etc.
Specifications
Model Number
VAC-CR-VHEM4LB
| Outer Diameter D | Length Under Neck | Radius R | Flute Length ℓ | Overall Length L | Shank Diameter d | Actual Effective Length Depends on Work Inclination Angle | Figure | |||||||
| 0.5° | 1° | 1.5° | 2° | 3° | ||||||||||
| 1 | 4 | 0.2 | 0.3 | 1.5 | 50 | 4 | 4.36 | 4.60 | 4.86 | 5.16 | 5.89 | 1 | ||
| 6 | 1.5 | 50 | 4 | 6.46 | 6.82 | 7.21 | 7.66 | 8.74 | 1 | |||||
| 8 | 0.2 | 1.5 | 50 | 4 | 8.57 | 9.04 | 9.56 | 10.15 | 11.18 | 1 | ||||
| 1.5 | 6 | 0.2 | 0.5 | 2.3 | 50 | 4 | 6.46 | 6.82 | 7.21 | 7.66 | 8.56 | 1 | ||
| 8 | 0.2 | 2.3 | 50 | 4 | 8.57 | 9.04 | 9.56 | 10.15 | 10.89 | 1 | ||||
| 10 | 2.3 | 50 | 4 | 10.67 | 11.26 | 11.91 | 12.53 | 13.23 | 1 | |||||
| 16 | 0.3 | 2.3 | 50 | 4 | 16.98 | 17.92 | 18.67 | 19.16 | 20.24 | 1 | ||||
| 2 | 6 | 0.5 | 3 | 50 | 4 | 6.46 | 6.82 | 7.21 | 7.66 | 8.27 | 1 | |||
| 8 | 0.2 | 0.5 | 3 | 50 | 4 | 8.57 | 9.04 | 9.56 | 10.04 | 10.60 | 1 | |||
| 10 | 0.3 | 0.5 | 3 | 50 | 4 | 10.67 | 11.26 | 11.91 | 12.25 | 12.94 | 1 | |||
| 12 | 0.2 | 0.3 | 0.5 | 3 | 50 | 4 | 12.77 | 13.48 | 14.09 | 14.47 | 15.28 | 1 | ||
| 14 | 0.5 | 3 | 50 | 4 | 14.88 | 15.70 | 16.25 | 16.68 | 17.61 | 1 | ||||
| 16 | 3 | 50 | 4 | 16.98 | 17.92 | 18.40 | 18.89 | 19.95 | 1 | |||||
| 3 | 10 | 0.2 | 0.5 | 4.5 | 50 | 6 | 10.97 | 11.57 | 12.24 | 13.00 | 13.73 | 1 | ||
| 12 | 0.2 | 0.3 | 0.5 | 4.5 | 50 | 6 | 13.07 | 13.79 | 14.59 | 15.22 | 16.07 | 1 | ||
| 16 | 0.2 | 0.3 | 0.5 | 1 | 4.5 | 60 | 6 | 17.28 | 18.23 | 19.13 | 19.64 | 20.74 | 1 | |
| 20 | 0.2 | 0.5 | 1 | 4.5 | 60 | 6 | 21.49 | 22.67 | 23.44 | 24.07 | 25.42 | 1 | ||
| 26 | 0.5 | 4.5 | 65 | 6 | 27.80 | 29.15 | 29.91 | 30.70 | 32.43 | 1 | ||||
| 4 | 10 | 0.3 | 0.5 | 1 | 6 | 50 | 6 | 10.97 | 11.57 | 12.14 | 12.46 | 13.16 | 1 | |
| 12 | 0.2 | 0.5 | 1 | 6 | 50 | 6 | 13.07 | 13.79 | 14.29 | 14.67 | 15.50 | 1 | ||
| 14 | 0.5 | 6 | 60 | 6 | 15.18 | 16.01 | 16.45 | 16.88 | 17.83 | 1 | ||||
| 16 | 0.2 | 0.3 | 0.5 | 1 | 6 | 60 | 6 | 17.28 | 18.13 | 18.60 | 19.10 | 20.17 | 1 | |
| 20 | 0.2 | 0.5 | 1 | 6 | 60 | 6 | 21.49 | 22.34 | 22.91 | 23.52 | 24.84 | 1 | ||
| 26 | 6 | 65 | 6 | 27.80 | 28.64 | 29.38 | 30.16 | 31.85 | 1 | |||||
| 30 | 0.5 | 1 | 6 | 70 | 6 | 32.01 | 32.84 | 33.69 | 34.58 | 36.52 | 1 | |||
| 35 | 1 | 6 | 70 | 6 | 37.16 | 38.09 | 39.08 | 40.11 | 42.36 | 1 | ||||
| 40 | 6 | 80 | 6 | 42.28 | 43.34 | 44.46 | 45.64 | 48.21 | 1 | |||||
| 6 | 20 | 0.2 | 0.3 | 0.5 | 1 | 9 | 60 | 6 | 20.78 | 21.30 | 21.85 | 22.43 | 23.69 | 2 |
| 30 | 0.3 | 0.5 | 1 | 15 | 90 | 6 | 31.02 | 31.81 | 32.63 | 33.49 | 35.37 | 2 | ||
| 8 | 25 | 0.3 | 0.5 | 1 | 12 | 70 | 8 | 26.19 | 26.85 | 27.54 | 28.27 | 29.86 | 2 | |
| 35 | 0.5 | 1 | 20 | 100 | 8 | 36.43 | 37.35 | 38.32 | 39.33 | 41.54 | 2 | |||
| 10 | 30 | 0.3 | 0.5 | 1 | 15 | 75 | 10 | 31.31 | 32.10 | 32.93 | 33.80 | 35.70 | 2 | |
| 40 | 0.5 | 1 | 25 | 100 | 10 | 41.56 | 42.60 | 43.70 | 44.86 | 47.38 | 2 | |||
| 12 | 32 | 0.5 | 1 | 18 | 80 | 12 | 33.36 | 34.20 | 35.08 | 36.02 | 38.04 | 2 | ||
| 50 | 30 | 110 | 12 | 46.68 | 47.85 | 49.09 | 50.39 | 53.22 | 2 | |||||
More Information
● High efficiency machining can be realized by suppressing chattering through the use of "unequal lead."
● Smooth chip discharge is achieved using an optimum groove geometry.
[ ! ]The electrical conductivity is minimal.
[ ! ]The actual effective length is a guideline. Confirm the actual measurement if concerned about interference with the workpiece.